Learning How To Bleed Air From Pool Pump (Sand Compatible)

Are you stressed because of the air trapped in your pool pump? Don’t worry! We have got a solution for you. Continue reading to find out!

Having air trapped in your swimming system is something you’ll undoubtedly experience regularly but, luckily, in several instances, it’s simple to fix. Below is our guide for how to bleed air from pool pump.

The Air Trapped In Your Pump

The most common spots you’re expecting to get air trapped will be in your pool pump strainer and filter housing. To drain the air, there is ordinarily a tiny pipe at the highest point of the filter to turn well over to allow the air to go out.

Removing air from a pool pipe requires purging water into the device to allow the pump to force out the air.

Don’t worry. This article contains a solution to this problem.

How To Know When You Have Trapped Air

You aren’t sure whether your pool pump has air in it? We have an incredible method for this problem as well.

There can be three different ways which are as follows:

  1. Having a look into the transparent lid of your pool motor strainer hardware can allow you to visualize the air. If you can observe water running from the reservoir into the container of the pool pump then it (evidently) isn’t complete of water.
  2. Your pool pump can create a distinct sound than it regularly does. It can do so, if it is attempting to squeeze air, or even a tiny volume of water and air, it can do so.
  3. There may be slight or no water flowing from your pool channels or waterfall if you have one although the pump operates on the filtration system or accumulates the setup. That will possibly be triggered at someplace by an airlock in the water system.

Why might air become trapped in your pool?

The most probable explanation is that you just purified the pool, and the stop-and-start motion to backwash and drain the pump has brought some air into the system.

If the level of water in your pool is minimal so that it does not cover the skimmer’s underside, this will permit air to enter the system and, of course, is an obvious answer by simply adding a nozzle to the water level. The less likely (luckily) is that air gets into the system somewhere else before it enters the pump.

How To Bleed Air From Pool Pump

If your pump strainer hardware is filled with air and after several minutes of operating, the motor water doesn’t begin flowing via it so it becomes filled then you will need to repair. So use the six step process below to learn the proper way how to bleed air from pool pump:

  1. Turn the pump off, and then use the forward valves to lock the skimmer boards. If you already have more than one skimmer, you can have separate feeds in the pump or even only one.
  2. Completely unlock the lower main drain valve which is at the base of your pool.
  3. Turn on the pump, and allow access to one of the skimmer valves a little at a moment.
  4. Ideally, you will begin to see a few air bubbles emerging from the back jets which will be the air moving through the pump.
  5. At this stage, you can try to eliminate any air that might have been stuck inside the filter housing.
  6. You must have lots of water passing through the process once the skimmer tubes are completely open and the air must be flown away.

Pool Pump Priming Methods

If the above method didn’t work, try following the steps given below for how to bleed air from pool pump with a priming-focused method.

  1. With the pump stopped, switch the knob of the multiport pump to the recirculation configuration so water does not pass via the filter but rather goes right back to the pool.
  2. Remove the lid from the pool pump strainer.
  3. Simply fill the machine via the strainer with a garden hose, and allow it to operate for a couple of minutes. It will begin filling the machine up to the skimmers.
  4. Place the strainer cap back on.
  5. Operate the pump till you see no air inside the pool pump system.
  6. Shut down the pump and reset the multiport lever to the filter setting before turning on the pump again.

Get Ready To Swim!

We hope that this article on how to bleed air from pool pump has helped you and the air is finally flown out if you followed the steps given above, accurately. We have tried our best to give the solution to your problem.

Now, you can swim again without any stress or worries!

Additional Recommended Resources